Geeetech® A10M Mix-color Prusa I3 3D Printer 220*220*260mm Printing Size
A part of the review has been auto-translated.
This is my first 3D printer but I have choosed it after viewing many youtube video and read many things about this and the A20M The A10M is cheapest than the A20M and the coast difference does not equal the quality evolution, it is why I have bought the A10M ! Now, the indications to assemble it are not perfect but it's easy to guess what to do except for inserting the filaments in the extrudors. I have spent many minuts to do it... I have updated the firmware to Marlin 1.1.9, then, the filaments had to go to the noze. I have printed the dog (from file on the 8G sd card) : the quality is good but it was very difficult to remove it from the bed. I have placed an order for a better bed.
received the printer is great packing. the spindle holders don't have any screws etc. the screen died mid way printing sample file. instructions are not clear on the assembling. but print quality is superb.
So far so good, i have not had any issues printing yet, the build was pretty straight forward, but I did have to straighten out the x carriage a bit before it would sit properly on the x axis. but other than that, it was very easy. Most of the issues I have had are with the slicing software, which is not a reflection on the hardware, as the test prints worked great. :) A very good printer. Not really for the beginner though,
Voici la liste des problèmes et changement que j’ai du apporter sur la Gtech A10M que j’ai acheté la semaine dernière avant de commencer l’impression. Un des 2 tubes PTFE était brisé et changé avec l’un des deux fournis. Les axes X et Y du chassis n’étaient pas à 90 degré l’un de l’autre ,corrigé en dévissant les 4 vis du joint central et en se servant de l’équerre pour replacé à 90 degré,comme il faut. L’axe X , les roulements étaient très mal ajustés il était impossible d’obtenir un niveau horizontal parfait, avec beaucoup d’effort en replaçant les roulements tout est revenu à l’état normal. Le ventilateur du bloc d’alimentation 24v est très bruyant ainsi que ceux de l’extruder. Le plateau chauffant est bombé de 1,3mm. entre les coins et le centre du plateau. Pas de plaque de verre fournie tel que montré sur photo de publicité Geeetech et Banggood. Un lot de vis est fourni en quantité presque industriel mais je vais y trouver un endroit ou les utilisés. Deux buses sont fournis avec mon imprimante, une de plus que prévus. Une seule feuille de montage était fournie, pour le manuel de l’utilisateur il faut se référer au site de Gtech. Pour la qualité d’impression et les modifications apportés à l’imprimante celle ci est de qualité ordinaire, le bltouch de tech pourrait il améliorer l’impression??? Pour la plaque de verre ,est ce que je peux m’attendre que Geeetech va me l’envoyer par courrier? je pose la question à Banggood! J’ai positionné les extruders sur des blocs et placer les supports filaments différemment pour simplifier l’opération de chargement filament. Photos incluses Positions des extruders et le plateau sans la plaque de verre.
Where can I buy the extruder block?!? I messed mine up!!!
I have received the 3d printer with all parts and with some spare parts. In the Easy to assemble and easy to operate. Print quality is quite good. The motors are quiet. There is 3 fans that makes a bit of noise.
the package has arrived in perfect condition very well packed.it is my first 3d printer, very easy to assemble. filament detector if activated fays out and does not print.lo disconnect and started working well now to see the first tests although only 1 comes on the sd
acabei de receber a impressora, vou montar e fazer os testes
Great after the A10 the a10m
It's working fine.