Could of been packages better for shipping mine arrived with bent pins would be nice if it came with long jumper caps but after straightening the pins and changing the jumpers all is well.

Could of been packages better for shipping mine arrived with bent pins would be nice if it came with long jumper caps but after straightening the pins and changing the jumpers all is well.

Could of been packages better for shipping mine arrived with bent pins would be nice if it came with long jumper caps but after straightening the pins and changing the jumpers all is well.

Bonne boîte à décades, pas ultra précise mais suffisant pour les bricoleurs, très utile pour le prototypage sur breadboard

Bonne boîte à décades, pas ultra précise mais suffisant pour les bricoleurs, très utile pour le prototypage sur breadboard

Bonne boîte à décades, pas ultra précise mais suffisant pour les bricoleurs, très utile pour le prototypage sur breadboard

Measured the basics (not all 10^7 combinations) is accurate enough. Good product.

Measured the basics (not all 10^7 combinations) is accurate enough. Good product.

Measured the basics (not all 10^7 combinations) is accurate enough. Good product.

haven’t tested yet but look to be ok.

haven’t tested yet but look to be ok.

haven’t tested yet but look to be ok.

English: Small 7 decades of good construction that goes up to 10Mohms by step of 1 ohm. Useful to look for the right value (CMS resistors are 1/2W to 1%) by trial and error on an assembly. Be careful, however, to choose standard values for a future installation because the 7-decade booklet allows all values from 1 to 10 million Ohms. With two of these small plates at €5, you can quickly install a stable and precise voltage divider to test a configuration. Residual resistance (when all riders are on 0) is quite low since less than 0.2 ohms. Very useful therefore and that should be found in all maker panoplies. English: Small 7 Decades, well made, that covers values from 1 Ohm up to 10 Mohms. Very useful to look for a value (resistors are SMD 1/2W 1%) by successive try on a test setup. Be careful to thing standard value for the final setup as the device can be set anywhere from 1 ohm up to 10 million ohms with 1 ohm steps. With 2 of these less than $6devices, you can build a precise and stable voltage divider to test a configuration. The residual value (all jumpers set to 0) is as low as 0.2 ohms. Very useful device that any maker should have.

Français : Petite 7 décades de bonne facture qui monte à 10Mohms par pas de 1 ohm. Utile pour chercher la bonne valeur (les résistances CMS sont des 1/2W à 1%) par tâtonnement sur un montage. Attention toutefois à choisir des valeurs standard pour un montage futur car la plaquette 7 décades permet toutes les valeurs de 1 à 10 millions d'Ohms. Avec deux de ces petites plaques à 5€, on peut monter rapidement un diviseur de tension stable et précis pour tester une configuration. La résistance résiduelle (quand tous les cavaliers sont sur 0) est assez faible puisque inférieure à 0,2 ohms. Très utile donc et qui devrait se trouver dans toutes les panoplies de maker. English : Small 7 décades, well made, that covers values from 1 Ohm up to 10 Mohms. Very useful to look for a value (resistors are SMD 1/2W 1%) by successive tries on a test setup. Be careful to chose standard value for the final setup as the device can be set anywhere from 1 ohm up to 10 millions ohms with 1 ohm steps. With 2 of these less than $6 devices, you can build a precise and stable voltage divider to test a configuration. The residual value (all jumpers set to 0) is as low as 0.2 ohms. Very useful device that any maker should have.

English: Small 7 decades of good construction that goes up to 10Mohms by step of 1 ohm. Useful to look for the right value (CMS resistors are 1/2W to 1%) by trial and error on an assembly. Be careful, however, to choose standard values for a future installation because the 7-decade booklet allows all values from 1 to 10 million Ohms. With two of these small plates at €5, you can quickly install a stable and precise voltage divider to test a configuration. Residual resistance (when all riders are on 0) is quite low since less than 0.2 ohms. Very useful therefore and that should be found in all maker panoplies. English: Small 7 Decades, well made, that covers values from 1 Ohm up to 10 Mohms. Very useful to look for a value (resistors are SMD 1/2W 1%) by successive try on a test setup. Be careful to thing standard value for the final setup as the device can be set anywhere from 1 ohm up to 10 million ohms with 1 ohm steps. With 2 of these less than $6devices, you can build a precise and stable voltage divider to test a configuration. The residual value (all jumpers set to 0) is as low as 0.2 ohms. Very useful device that any maker should have.

fast delivery and ok.

fast delivery and ok.

fast delivery and ok.

Very good product as usual

Very good product as usual

Very good product as usual

Hi Today: The 200V 1R - 9999999R Seven Decade Programmable Adjustable... has arrived.. Thank You very much for Processing and Shipping my ORDER.. Have a Great Day.. William Oxner

Hi Today: The 200V 1R - 9999999R Seven Decade Programmable Adjustable... has arrived.. Thank You very much for Processing and Shipping my ORDER.. Have a Great Day.. William Oxner

Hi Today: The 200V 1R - 9999999R Seven Decade Programmable Adjustable... has arrived.. Thank You very much for Processing and Shipping my ORDER.. Have a Great Day.. William Oxner

I received this item yesterday and I was able to use it right away on a project I just started. I didn’t have a certain resister and having the 200V 1r-9999999r module it paid off right away, good item to have in your box of tricks when working with electronics.

I received this item yesterday and I was able to use it right away on a project I just started. I didn’t have a certain resister and having the 200V 1r-9999999r module it paid off right away, good item to have in your box of tricks when working with electronics.

I received this item yesterday and I was able to use it right away on a project I just started. I didn’t have a certain resister and having the 200V 1r-9999999r module it paid off right away, good item to have in your box of tricks when working with electronics.

Lots of practicality

muita praticidade

Lots of practicality