Customer Reviews

4.97 out of 5
Write a Review
  • All Reviews (69)
  • Image (7)
  • Video (0)
  • All Star
    • All Star(69)
    • 5 Star(67)
    • 4 Star(2)
    • 3 Star(0)
    • 2 Star(0)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (Indonesia)
  • Mundek
    February-06 2016 10:13:51

    Installed two of them on two different Devo transmitters and both work great. Lets you to fly many drones, quadcopters, hexacopters, boats, cars, planes, helicopters, etc. Highly Recommended.

  • September-29 2016 12:52:52

    It works as expected and now I can fly my Hubsan X4 with my Devo 7e (it even has voltage telemetry)! It does not include any wires or directions, so do a little homework beforehand. I used the 'new wiring' for the install. Basically, pad 6 gets bridged to 9, and 7 gets bridged to 8. The photo included shows the other connections, but the pads haven't been bridged in this case. TXEN gets connected to GI01 and RXEN gets connected to GI02 instead of GND and VCC as shown. Every pad will have just one

  • May-05 2016 12:25:51

    This module arrived in good shape. I added this module to my Devo7E transmitter and it works perfectly. I tested it on a Husban quad and it was able to bind immediately. This was the second module that I've added to my transmitter and I've experienced perfect radio communication with it. I've flow it out as far as I can see/control the quad and had perfect control the whole time - no range issues. I'm very happy with this product.

  • March-07 2017 08:33:57

    As decribed

  • April-08 2016 16:43:19

    Have it installed on my Devo7e and everything works as expected. Soldering was easy and i´m happy about that everything works ;) Thx Banggood !

  • September-12 2017 18:08:04

    great tx module to complete my multi Tx FrSky Taranis Module

  • February-28 2017 03:11:05

    Works perfectly on my DEVO 7e.

  • February-21 2020 00:44:44

    good quality small sized transceiver module

  • April-11 2016 20:50:09

    Very happy with the purchase. Now I can control the Hubsan X4 flight controller with Walkera Devo10. With greatly extended control range. Follow the instructions on the picture. VCC wire goes to 3.3V and black to TMS, which is marked on the board inside your radio. Once wiring is completed, enable module in file. enable-a7105 = A13 has_pa-a7105 = 1 If you don't want to configure model, add settings from forums into your model file. Enjoy

  • April-10 2015 06:10:53

    Не хотел запаивать модули непосредственно к плате аппаратуры. Вывел с платы своего Devo10E два шлейфа с 6-пиновыми jst коннектороми, зацепил такие же шлейфы на модули, этот и NRF24L01 так же с коннекторами на конце. Соединил их и получил


    Total 0 pages

    Go to page


    You might be interested in

    recommendation for you
    • Rp660,601.12
    • Rp1,516,506.67
    • Rp243,093.20
    • Rp2,146,059.40
    • Rp1,720,538.99
    • Rp55,515.10
    • Rp137,070.80
    • Rp101,300.76
    • Rp1,001,418.08
    • Rp1,573,738.74
    • Rp3,124,298.49
    • Rp1,659,586.84
    • Rp157,245.10
    • Rp200,169.15
    • Rp1,308,611.19
    • Rp446,839.36
    • Rp493,197.33
    • Rp536,407.54