Customer Reviews

4.97 out of 5
Write a Review
  • All Reviews (34)
  • Image (3)
  • Video (1)
  • All Star
    • All Star(34)
    • 5 Star(33)
    • 4 Star(1)
    • 3 Star(0)
    • 2 Star(0)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (Indonesia)
  • August-24 2019 06:39:23

    Карбюратор на вид и по качеству литья хороший, только на фотографии он с латунной заслонкой, пришёл карбюратор с черной вроде алюминиевой заслокой, и на нем нету надписи микуни, будут устанавливать на мотоцикл ява 638, как установлю напишу как и что.

  • June-14 2017 03:23:52

    I installed this carburetor in a KMX125. The bike started immediately. There is a connector for a vacuum, or oil, line at the front of the carburetor. This needs to be blocked off if not used. The bike ran very well after adjusting the air, and idle screws. I was surprised that no further adjustment was needed. This seem to be a copy of a Mikuni VM26 carburetor. Note on the one photo that the lid of the slide of the Mikuni fitted on this carburetor. The finish is not the highest quality, but much

  • January-29 2019 19:22:06


  • September-30 2020 04:18:32

    All good. Nice carburettor.

  • September-30 2020 04:12:35

    good quality will definitely use banggood again.

  • June-14 2020 12:06:01


  • November-30 2016 05:16:48

    I ordered this carburetor for my DT 50 LC with a 47 mm cylinder bore (80 cc) because the stock carb wasn't keeping up with the cylinder new needs. It performs quite nicely but it's not easy to tune for an unexperienced user. I won't give it 5 stars because the first one that I got broke the idle screw and the supplier was a bit difficult about sending a replacement item, which I ended up on receiving when I did a video showing the problem. You can see the videos here: Unboxing Broken

    Comments (2)
  • April-17 2017 16:32:54

    en conservant le boisseau d'origine j'ai pu l'adapter sur une 125 DTLC YPVS mais aucune références gravé sur les gicleurs le filetage gicleurs des vrais Mikuni n'est pas le même !

    Comments (1)
  • July-28 2015 01:46:59

    Хороший карбюратор. Устанавливал на восход 3, двигатель стал работать ровнее и мягче. Подробнее можно почитать в обзоре

  • July-11 2019 03:52:40

    コマジェに使用 オーバーフロー油面調整してもダメ フロートの浮力が足りない、 分岐してタンクへリターンしてオーバーフローが止まった. 燃ポン付きには不向き。


    Total 0 pages

    Go to page


    You might be interested in

    recommendation for you
    • Rp405,918.43
    • Rp779,500.74
    • Rp198,452.19
    • Rp593,067.29
    • Rp136,069.24
    • Rp207,466.24
    • Rp249,388.73
    • Rp231,217.55
    • Rp182,856.45
    • Rp116,324.17
    • Rp127,341.35
    • Rp594,641.17
    • Rp434,391.38
    • Rp244,094.76
    • Rp248,673.33
    • Rp160,822.11
    • Rp171,696.20
    • Rp732,141.21