It's a very high quality frame First you open the box and you'll see a lot of parts and screws The screws are packaged by size and up to size representation Carbon parts are cut cleanly and DIATONE on the upper plate.The bottom plate is vacuum-packed with Roma lettering The screw heads are specially and cleanly chamfered, and even the motor mounting screws are provided with the same thing The accuracy of the screw holes is high and the screws are dropped slightly The stack hole is set to 20x20 30.5x30.5 (with seat) in the center, and 20x20 (with seat) in the rear are set to be shifted back and forth in three stages The camera mounts are 19 and 20mm by changing the left and right sides Antenna mount supports VTX antennas, 2.4G and CrossFire antennas The standoff height is a little tight, 23mm Board of RunCam hybrid4K with isolated plates in ESC and FC size conversion of 30.5X30.5 to center CAP(x2) insulated plate VTX insulated plate in the rear insulated plate receiver configuration Others Top plate front tip GPS behind 4S/1800mAh Stand up the VTX antenna and receiver antenna by using other mounts instead of using the supplied antenna mount (^-^) It's still in the tentative stage, but I'm very satisfied with it (^-^) I won't miss buying it! It's cheap, but it's a very recommended frame! It comes with a camera mount that doesn't seem to work (laughs)

めっちゃクオリティの高いフレームです まず箱を開けると たくさんのパーツやビスが出てきます ビスはサイズごとにパッケージングされサイズ表記までされてます カーボンパーツは綺麗に断面処理されアッパープレートにはDIATONE ボトムプレートにはRomaの文字が彫り込まれ真空パックされてます ビスの頭は特殊で綺麗に面取りされており モーター取り付けビスまで同じ物で用意されてます ビス穴の精度は高くビスを少し落とし込む様に座グリ処理までされてます スタックホールはセンターに20x20 30.5X30.5(座グリあり) リヤには20x20(座グリあり)を3段階で前後にずらせる様になってます カメラマウントは左右を入れ換えることで19と20mmに対応してます アンテナマウントはVTXアンテナと2.4G及びCrossFireアンテナに対応してます スタンドオフの高さは23mmと少々タイトですが センターに30.5X30.5のESCとFC サイズ変換で絶縁プレートとRunCam hybrid4Kのボード リヤにCAP(x2) 絶縁プレート VTX 絶縁プレート レシーバーの構成で収まりました その他は トッププレートフロント先端にGPS その後ろに4S/1800mAh 付属のアンテナマウントは使わずに他のマウントを流用してVTXアンテナとレシーバーアンテナを立てます(^-^) まだ仮組段階ですが 大満足の仕上がりになりました(^-^) 買って損はしません！ 安いですが めっちゃお薦めのフレームです！ 補足ですが 使えなさそうなカメラマウントも付いてきます(笑)

It's a very high quality frame First you open the box and you'll see a lot of parts and screws The screws are packaged by size and up to size representation Carbon parts are cut cleanly and DIATONE on the upper plate.The bottom plate is vacuum-packed with Roma lettering The screw heads are specially and cleanly chamfered, and even the motor mounting screws are provided with the same thing The accuracy of the screw holes is high and the screws are dropped slightly The stack hole is set to 20x20 30.5x30.5 (with seat) in the center, and 20x20 (with seat) in the rear are set to be shifted back and forth in three stages The camera mounts are 19 and 20mm by changing the left and right sides Antenna mount supports VTX antennas, 2.4G and CrossFire antennas The standoff height is a little tight, 23mm Board of RunCam hybrid4K with isolated plates in ESC and FC size conversion of 30.5X30.5 to center CAP(x2) insulated plate VTX insulated plate in the rear insulated plate receiver configuration Others Top plate front tip GPS behind 4S/1800mAh Stand up the VTX antenna and receiver antenna by using other mounts instead of using the supplied antenna mount (^-^) It's still in the tentative stage, but I'm very satisfied with it (^-^) I won't miss buying it! It's cheap, but it's a very recommended frame! It comes with a camera mount that doesn't seem to work (laughs)

Really nice frame, one of the most beautiful 5'' frames. Every part is high end quality, every screw, frame part, plastic parts look so premium. You get assembly diagram and in 30 mins you will assemble it. You will also get a lot of spare and additional parts like screws and gaskets. Fast delivery and 5 stars product

Really nice frame, one of the most beautiful 5'' frames. Every part is high end quality, every screw, frame part, plastic parts look so premium. You get assembly diagram and in 30 mins you will assemble it. You will also get a lot of spare and additional parts like screws and gaskets. Fast delivery and 5 stars product

Really nice frame, one of the most beautiful 5'' frames. Every part is high end quality, every screw, frame part, plastic parts look so premium. You get assembly diagram and in 30 mins you will assemble it. You will also get a lot of spare and additional parts like screws and gaskets. Fast delivery and 5 stars product

really nice frame thin arms but other then that i love it

really nice frame thin arms but other then that i love it

really nice frame thin arms but other then that i love it

STDver will be the third (^-^) Cheap and strong on my favorite aircraft. Highly recommended frame (^-^) The DJIver and STDver each fly with RunCam hybrid4K and GPS, T-motor's Blackbird V2 and BMS Raptor, but the high-pitch prop is over 180km/h high power aircraft It's an overspec for a beginner amateur, and I think I punched out a bit during the trick, but I'm flying to a hell of a place I'm thrilled when I fly between structures and trees Just because I'm nervous about drifting stones, I built the Choi-flying aircraft that can fly comfortably This frame is surprisingly light, 2205/2300kv, and even older non-force motors fly well (^-^) The sturdy makes it perfect for training choy flyers I'm going to make a spare machine for the Choi aircraft and I'm going to purchase additional items For 2205, 35A of FCinESC is enough If you're flying Choi, the VTX is also cheap about $15-20 and 200-400mW is fine (^-^) With this frame, you can build a low-cost, good-looking aircraft that can fly comfortably and well (^-^) We can handle both low-cost and high-spec machines I can recommend it. It's a great frame (^-^)

STDverは3機目になります(^-^) お気に入りの機体で 安くて丈夫 お薦めのフレームです(^-^) DJIverとSTDver各一機はRunCam hybrid4KとGPS搭載しT-motorのBlackbirdV2とBMS Raptorで飛ばしてますが ハイピッチのプロップにすると180km/hを超えるハイパワー機です 初心者素人の私にはオーバースペックで トリックの際に少しパンチアウトしたつもりが とんでもないとこまで飛んでいきますw ストラクチャーや木々の間を飛行する時はドキドキしますw ただ流石に気が張るので 気持ち良く気楽に飛ばせるチョイ飛ばし用機体をビルドしたところ このフレームが意外と軽く2205/2300kvで旧型の非力モーターでも良く飛びます(^-^) 頑丈なのでチョイ飛ばしのトレーニングにも最適です チョイ飛ばし機のスペア機を作ろうと思い追加購入です 2205ならFCinESCの35Aで十分ですし チョイ飛ばしならVTXも安い15～20ドル位で200～400mWでいいです(^-^) このフレームがあれば ローコストで見映えが良く 気持ち良く元気にフライトできる機体がビルドできます(^-^) ローコスト機でもハイスペック機でも対応できる お薦めできる 素晴らしいフレームです(^-^)

STDver will be the third (^-^) Cheap and strong on my favorite aircraft. Highly recommended frame (^-^) The DJIver and STDver each fly with RunCam hybrid4K and GPS, T-motor's Blackbird V2 and BMS Raptor, but the high-pitch prop is over 180km/h high power aircraft It's an overspec for a beginner amateur, and I think I punched out a bit during the trick, but I'm flying to a hell of a place I'm thrilled when I fly between structures and trees Just because I'm nervous about drifting stones, I built the Choi-flying aircraft that can fly comfortably This frame is surprisingly light, 2205/2300kv, and even older non-force motors fly well (^-^) The sturdy makes it perfect for training choy flyers I'm going to make a spare machine for the Choi aircraft and I'm going to purchase additional items For 2205, 35A of FCinESC is enough If you're flying Choi, the VTX is also cheap about $15-20 and 200-400mW is fine (^-^) With this frame, you can build a low-cost, good-looking aircraft that can fly comfortably and well (^-^) We can handle both low-cost and high-spec machines I can recommend it. It's a great frame (^-^)

STD is the second, and the third with DJIver The first aircraft was a RunCam hybrid4K and GPS-equipped aircraft The stack space is a little low, and it's hard to layer That's enough Since it's a Freestyle machine, there's stack space on the back of the fuselage There's also some space behind the camera The frame is very clean, there are many spare parts, screws, etc., and I think it's the best cost performance The second DJIver. This frame is similar to the STDVer, but most parts are designed specifically There are three stack spaces behind the camera, the center, and the back, the height is the same as STDver RunCam Turn the hybrid4K GPS 2307 at 4S/3000mAh I'm flying on CrossFire, but I'm overspecified for a novice amateur The camera cage is strong and the timing was slow when I made it soaring, but the camera and the aircraft were safe w Sturdy, well built and cheap for about $50 I thought that this frame would be good even for the aircraft for flying with a powerless motor...I built the third aircraft(^-^) It's a surprisingly light frame and flies well even at 2205/2300 kv Ordered a fourth plane to make a spare plane to fly Choi and wait for arrival(^-^) The GPS (180) is placed near the camera and the 4S/1800mAh is right behind it

STDは2機目 DJIver入れると3機目になります 1機目はRunCam hybrid4KとGPSを搭載した機体で スタックスペースがやや低く レイヤーし難いですが 十分ではあります Freestyle機なので胴体の後方側にもスタックスペースがあります カメラ後方にも多少のスペースがあります フレームの造りはとても綺麗で スペアのパーツやビス等の付属品が多く コストパフォーマンスは最高だと思います 2機目はDJIver このフレームはSTDverと似てますが ほとんどのパーツが専用設計です カメラ後方とセンター それから後方の3ヵ所にスタックスペースがあり 高さはSTDverと同じです RunCam hybrid4K GPS 2307を4S/3000mAhで回し CrossFireで飛行させてますが 初心者素人の私にはオーバースペックですw カメラケージ頑丈で 一度 急上昇させた際にタイミングが遅く鉄骨に正面からぶつかりましたが カメラも機体も無事でしたw 丈夫で造りが良く50ドル程で安く 非力なモーターでチョイ飛ばし用の機体でもこのフレームがいいな・・・と思い3機目をビルドしました(^-^) 意外と軽いフレームで 2205/2300kvでも良く飛びます チョイ飛ばし用のスペア機を作ろうと4機目を注文 到着待ちです(^-^) GPS(180)をカメラ付近に取り付け その後方に4S/1800mAhが丁度良く搭載できます

STD is the second, and the third with DJIver The first aircraft was a RunCam hybrid4K and GPS-equipped aircraft The stack space is a little low, and it's hard to layer That's enough Since it's a Freestyle machine, there's stack space on the back of the fuselage There's also some space behind the camera The frame is very clean, there are many spare parts, screws, etc., and I think it's the best cost performance The second DJIver. This frame is similar to the STDVer, but most parts are designed specifically There are three stack spaces behind the camera, the center, and the back, the height is the same as STDver RunCam Turn the hybrid4K GPS 2307 at 4S/3000mAh I'm flying on CrossFire, but I'm overspecified for a novice amateur The camera cage is strong and the timing was slow when I made it soaring, but the camera and the aircraft were safe w Sturdy, well built and cheap for about $50 I thought that this frame would be good even for the aircraft for flying with a powerless motor...I built the third aircraft(^-^) It's a surprisingly light frame and flies well even at 2205/2300 kv Ordered a fourth plane to make a spare plane to fly Choi and wait for arrival(^-^) The GPS (180) is placed near the camera and the 4S/1800mAh is right behind it

Everything is excellent! quality as always at the height

все отлично! качество как всегда на высоте

Everything is excellent! quality as always at the height

Everything from the screws to the carbon fiber and packaging is really high quality. All the pieces fit together perfectly and building this frame was a breeze, especially compared to some knock-off crappy frames I have bought before! Would highly recommend!

Everything from the screws to the carbon fiber and packaging is really high quality. All the pieces fit together perfectly and building this frame was a breeze, especially compared to some knock-off crappy frames I have bought before! Would highly recommend!

Everything from the screws to the carbon fiber and packaging is really high quality. All the pieces fit together perfectly and building this frame was a breeze, especially compared to some knock-off crappy frames I have bought before! Would highly recommend!

In accordance with the description received in a Diatone box, in a bag without too much protection, waiting to mount it to check the conformity of the Frame and test it in flight.

Conforme à la description reçu dans une boîte Diatone, dans un sachet sans trop de protection, dans l’attente de le monter pour vérifier la conformité de la Frame et l’essayer en vol.

In accordance with the description received in a Diatone box, in a bag without too much protection, waiting to mount it to check the conformity of the Frame and test it in flight.

i cahnge with mamba stack

i cahnge with mamba stack

i cahnge with mamba stack

a hammer frame, bought two of them directly

ein Hammer Frame, direkt zwei davon gekauft

a hammer frame, bought two of them directly