Customer Reviews

4.95 out of 5
Write a Review
  • All Reviews (598)
  • Image (63)
  • Video (0)
  • All Star
    • All Star(598)
    • 5 Star(577)
    • 4 Star(14)
    • 3 Star(5)
    • 2 Star(0)
    • 1 Star(2)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (Indonesia)
  • March-12 2020 17:39:35


  • October-15 2020 12:39:23

    very nice

  • August-13 2020 09:19:05


  • June-14 2017 15:45:34

    Die vorgestellten Nozzles sind als Reserve für meine V6 Extruder gekauft. Bisher waren die Messing Nozzles von Banggood immer ein sehr guter Kauf. Und ich denke, dass die hier angebotenen Nozzles in den Größen: 0,2 mm, 0,3 mm, 0,4 mm und 0,5 mm - jeweils 2 Stück - dafür hervorragend geeignet sind. ----------------- The presented Nozzles are bought as reserve for my V6 extruder. So far the brass Nozzles from Banggood were always a very good purchase. And I think that the Nozzles offered in the

  • okercho
    January-11 2017 12:49:54

    NOTE: I didn't test it yet with the extruder Quality seem to be OK, size is perfect and nozzle hole is centered. As can be seen in pictures, 0.3 hole seems to be bigger than 0.2 (from left to right, 0.2, 0.3, 0.4 and 0.5). I'm not quite sure about nozzle hole size, but I cannot compare it with any other nozzle. The number to identify it is OK, although if the nozzle is dirty with plastic I think it could be tricky to read.

  • August-23 2016 19:33:49

    Recieved quickly from supplier at good price. Under inspection the hole sizes are consistent. Threads are within tolerances for the heated heads I have. Size writing is clear on the one side of the nozzle but may become difficult to see if nozzle becomes dirty from use later. An engraved size lettering may be better. Photo shows the lineup of product pairs from largest to smallest diameter.

  • May-24 2017 04:17:32

    Boquillas para el extrusor de la impresora 3D BQ, buen material .

    Comments (1)
  • September-20 2018 22:10:32

    Отличный набор дюз разного диаметра. Использую на принтере Anet A6, в зависимости от особенности 3д детали. Для более качественной и точной печати использую 0.2мм. Для более грубой и быстрой - 0.5мм.

  • May-17 2017 04:27:45

    Качественно изготовленные сопла для 3Д-принтера. Проверял под микроскопом: отверстия пробиты строго по центру (я ранее заказывал в другом магазине - отверстия были не совсем круглые и сдвинуты относительно центра). В результате эти сопла печатают намного аккуратнее старых.

  • September-15 2016 11:29:42

    Kam wie ueblich gut verpackt bei mir an. Verarbeitung auf den ersten Blick voll in Ordnung. Habe zur Zeit noch nichts damit gedruckt, aber ich denke die Duesen werden keine Probleme machen. Duesenoeffnung ist bei allen zentriert mittig. Oeffnungsdurchmesser stimmt auch. Preis / Leistung unschlagbar.


    Total 0 pages

    Go to page


    You might be interested in

    recommendation for you
    • Rp146,429.55
    • Rp107,039.14
    • Rp125,735.31
    • Rp107,181.86
    • Rp84,632.28
    • Rp104,755.64
    • Rp82,491.50
    • Rp160,558.71
    • Rp203,945.24
    • Rp47,668.10
    • Rp213,364.69
    • Rp236,199.70
    • Rp249,329.84
    • Rp58,229.29
    • Rp72,358.46
    • Rp110,892.55
    • Rp502,798.53
    • Rp73,785.65