Precise details:
MATEKSYS CRSF-PWM-6 CRSF to PWM Converter 6 PWM 50-400Hz Output 2 UARTS External Current Sensor Failsafe Auto Set for RC Receiver
Specifications:
Brand Name: MATEKSYS
Item Name: CRSF-PWM-6 Converter
Model: CRSF-PWM-6
Weight: 1.3g
Size: 25x16mm
Compatible with CRSF protocol receiver only
6x PWM outputs (frequency 50-400Hz)
PWM frequency configurable (50Hz default, 100,160,330, 400Hz)
2x UARTs (for Receiver and GPS)
Telemetry ID: RxBt, Curr, Capa, Bat%, GPS, GSpd, Hdg, Alt, Sats
36V Max. battery voltage sense (1K:10K voltage divider built-in)
Compatible with external Current sensor (0~3.3V)
Vbat and Current sensor scale configurable
Failsafe value auto set
Firmware upgradeable
Rated voltage: 4~9V @5V pad, 0~36V @Vbat, 0~3.3V @Curr
No 5V regulator built-in
Pinouts and Pads:
Tx1/Rx1(UART1) for CRSF protocol Receiver
Tx2/Rx2(UART2) for GPS/firmware update/setting parameters
1~10: CH1~CH10 PWM outputs
Curr: current sensor signal (0~3.3V)
Vbat: Battery voltage sensing (0~36V)
G: ground
4v5 pad voltage = 5V pad voltage -0.3V, make sure the voltage on 5V pad is not higher than receiver and GPS rated voltage.
Failsafe:
Failsafe value is set automatically after CRSF-PWM board is powered on and receive CRSF signal. LED blinks 8 times quickly.
Failsafe value = The PWM value of each channel(except CH3) when CRSF signal is received by CRSF-PWM board for the first time
CH3 is specially arranged for the throttle, Failsafe value = 988 by default.
Usually put the Throttle joystick to the lowest point, put AIL(Roll), ELE(Pitch), RUD(Yaw) middle before powering on receiver.
LED status:
slow blinks: CRSF-PWM board doesn’t receive CRSF signal, e.g., receiver is not bound with transmitter, receiver is not connected to UART1 of CRSF-PWM board.
8x quick blinks: CRSF-PWM board received CRSF signal and failsafe value is saved.
solid ON: CRSF-PWM board and receiver are working normally
2x slow blinks between 8x fast blink and solid on: CLI mode is active
GPS telemetry:
Compatible with GPS NMEA protocol
GPS “TX†to CRSF-PWM board “RX†Single wire half duplex UART connection, CRSF-PWM board “TX†to GPS “RX†is not essential.
Support GPS Telemetry ID: GPS, GSpd, Hdg, Alt, Sats
u-blox series GPS can output “0+1 – UBX+NMEA†protocol by default
Sensors(GPS, GSpd, Hdg, Alt, Sats) will blink in Transmitter TELEMETRY tab once CRSF-PWM board has connection with GPS.
Troubleshooting for no GPS telemetry, double check the wiring between GPS and CRSF-PWM board, some u-blox GPS may don’t output NMEA protcol, you need to be reverted GPS to default configuration in u-center.
TIM & PWM Frequency:
PWM frequency on all 10x Channels can be configured according to TIM
PWM run at 50Hz by default
TIM2: CH1, CH2, CH4
TIM16: CH3
TIM3: CH5, CH6, CH7, CH8
TIM1: CH9, CH10
CLI mode:
If CRSF-PWM board doesn’t detect GPS connected to UART2 within 10 seconds after powering on, CLI mode will active.
After CLI mode is active, CRSF-PWM board can be connected to configurator via USB-TTL module/FC passthrough.
in CLI mode, CRSF-PWM board firmware can be updated
CLI mode has no effect to receiver CRSF signal and PWM outputs
Package included:
1 x CRSF-PWM-6 Converter
1 x Dupont 2.54 pins