perfecto excelente

perfecto excelente

perfecto excelente

Very Good

Very Good

Very Good

Practical helper in machining thin parts. Comparison of a common tip with an extended tip. It can be seen that the tool gets close to drilling and is easier to machine.

Praktický pomocník při obrábění tenkých součástek. Porovnání běžného hrotu s prodlouženým hrotem. Je vidět že se nástroj dostane blízko k navrtání a snáze se obrábí.

Practical helper in machining thin parts. Comparison of a common tip with an extended tip. It can be seen that the tool gets close to drilling and is easier to machine.

Körnerspitze hat im vorderen Teil einen Rundlauf von einem 1/2 100 mm! Das ist ein sehr guter Wert! Körner ist gut verarbeitet, hat ein sauberes Finish. Würde ich wieder kaufen!

Körnerspitze hat im vorderen Teil einen Rundlauf von einem 1/2 100 mm! Das ist ein sehr guter Wert! Körner ist gut verarbeitet, hat ein sauberes Finish. Würde ich wieder kaufen!

Körnerspitze hat im vorderen Teil einen Rundlauf von einem 1/2 100 mm! Das ist ein sehr guter Wert! Körner ist gut verarbeitet, hat ein sauberes Finish. Würde ich wieder kaufen!

Excellent craftmanship and performance with near zero runout at a very good price. Nice, small point makes end facing simple. Only minus is that the protruding MT2 small end reduces my quill travel 1/2", but I guess that will be cut/ ground off one of these days.

Excellent craftmanship and performance with near zero runout at a very good price. Nice, small point makes end facing simple. Only minus is that the protruding MT2 small end reduces my quill travel 1/2", but I guess that will be cut/ ground off one of these days.

Excellent craftmanship and performance with near zero runout at a very good price. Nice, small point makes end facing simple. Only minus is that the protruding MT2 small end reduces my quill travel 1/2", but I guess that will be cut/ ground off one of these days.

Very well made product from look and finish. Theres one problem on my lathe: The MT2 shank is a few millimeters to short. I can't stroke back the tailstock far enought to release it. All other orderes MT2 shank parts from Banggood don't have this problem! Luckily I noticed the shank is not hardend, so I will bore in, tap a thread and just put a screw in - Problem solved.

Very well made product from look and finish. Theres one problem on my lathe: The MT2 shank is a few millimeters to short. I can't stroke back the tailstock far enought to release it. All other orderes MT2 shank parts from Banggood don't have this problem! Luckily I noticed the shank is not hardend, so I will bore in, tap a thread and just put a screw in - Problem solved.

Very well made product from look and finish. Theres one problem on my lathe: The MT2 shank is a few millimeters to short. I can't stroke back the tailstock far enought to release it. All other orderes MT2 shank parts from Banggood don't have this problem! Luckily I noticed the shank is not hardend, so I will bore in, tap a thread and just put a screw in - Problem solved.

Finish and appearance is exellent. The run out is almost undetectable, i.e., below 0.003 mm.

Finish and appearance is exellent. The run out is almost undetectable, i.e., below 0.003 mm.

Finish and appearance is exellent. The run out is almost undetectable, i.e., below 0.003 mm.

I needed a small live center for my MT2 tailstock. This live center is a perfect companion to my regular sized one (I like the size of it). The morse taper shank is a bit short and has no thread at the end. This can be easily fixed with a lathe. I'll add a threaded bore so I can put a bolt into it (for easier extraction) . The quality of the bearing is nothing to write home about. I'll see how it stands up to use. Glad I have it. The price is excellent.

I needed a small live center for my MT2 tailstock. This live center is a perfect companion to my regular sized one (I like the size of it). The morse taper shank is a bit short and has no thread at the end. This can be easily fixed with a lathe. I'll add a threaded bore so I can put a bolt into it (for easier extraction) . The quality of the bearing is nothing to write home about. I'll see how it stands up to use. Glad I have it. The price is excellent.

I needed a small live center for my MT2 tailstock. This live center is a perfect companion to my regular sized one (I like the size of it). The morse taper shank is a bit short and has no thread at the end. This can be easily fixed with a lathe. I'll add a threaded bore so I can put a bolt into it (for easier extraction) . The quality of the bearing is nothing to write home about. I'll see how it stands up to use. Glad I have it. The price is excellent.

pas de jeu propre tourne bien et en douceur , pas de jeu , cone mt2 qui va bien ..

pas de jeu propre tourne bien et en douceur , pas de jeu , cone mt2 qui va bien ..

pas de jeu propre tourne bien et en douceur , pas de jeu , cone mt2 qui va bien ..

Great.

Ottimo.

Great.