It's a cheap and light frame As I wrote last time, the frame is not cut and there is no cross-section treatment, and when I touch it it it becomes black (laughs) I re-purchased to build another training machine (^-^) The basics of this aircraft are 4x35A (Burst 40A) ESC 20x20 Stack with FC 500mW VTX&lollipop3 Jumper R1 RX 5" props can top mount the battery, but 4S/1500mAh is only This specification from last time, but it's just as good as a little deviation (laughs) It weighs a little 460g (no prop nut in the photo) Although there is room for abolition of antenna pipes and further lightening in VTX VTX antenna receivers It's cheap and it's good to fly, and it's a long flight (^-^) For 5.5-inch props, the battery uses 4S/1800mAh I also use the battery protector, which makes it even heavier Flight time simply increased It's a little quiet because it can make the pitch shallower (laughs) It weighs about 490g (also without prop nut) I'm always quadrupling with no weight The Racing Quad was built with a slightly expensive frame of about 310g (no battery), but I think it would be the same if I removed the LEDs and shark fins, but it's more than double the cost It's also 4S/1500mAh and a little 3 minutes From there, I'm flying a little 3 minutes in 4S/850mAh, so I think I've got a pretty good quad.(^-^)

安くて軽いフレームです 前回も書きましたがフレームは切りっぱなしで断面処理は無く 触ると黒く汚れます(笑) もう一機同じ練習機を造りたくて再購入しました(^-^) 今回の機体の基本は FC内蔵4x35A(バースト40A)ESC 20x20スタック 500mW VTX&lollipop3 jumper R1 RX 5インチプロップの場合はバッテリーをトップマウントできますが4S/1500mAhはギリギリです 前回からこの仕様ですが 少々ズレても大丈夫な程度のギリギリ具合です(笑) 重量は460g少々(写真ではプロップナット未装着) アンテナパイプの廃止やVTX VTXアンテナ レシーバーで更なる軽量化の余地はありますが 安くてそこそこの性能でそこそこよく飛び なかなかロングフライトができます(^-^) 5.5インチプロップの場合はバッテリーは4S/1800mAhを使ってます バッテリープロテクターも使ってますので更に重くなってますが フライト時間は単純に増加しました ピッチを浅くできるので 少し静かです(笑) 重量は490gほどです(同じくプロップナット未装着) いつも重量を気にせずクワッドを組んでますが 少し高価なフレームで造ったレーシングクワッドが約310g(バッテリーなし)ほどでしたがLEDやシャークフィンを外せば同じ位になるかと思います ですがコストは倍以上です 飛行時間も4S/1500mAhで3分少々です そこから考えると4S/850mAhで3分少々飛びますので なかなかいいクワッドが出来たと思います(^-^)

It's a cheap and light frame As I wrote last time, the frame is not cut and there is no cross-section treatment, and when I touch it it it becomes black (laughs) I re-purchased to build another training machine (^-^) The basics of this aircraft are 4x35A (Burst 40A) ESC 20x20 Stack with FC 500mW VTX&lollipop3 Jumper R1 RX 5" props can top mount the battery, but 4S/1500mAh is only This specification from last time, but it's just as good as a little deviation (laughs) It weighs a little 460g (no prop nut in the photo) Although there is room for abolition of antenna pipes and further lightening in VTX VTX antenna receivers It's cheap and it's good to fly, and it's a long flight (^-^) For 5.5-inch props, the battery uses 4S/1800mAh I also use the battery protector, which makes it even heavier Flight time simply increased It's a little quiet because it can make the pitch shallower (laughs) It weighs about 490g (also without prop nut) I'm always quadrupling with no weight The Racing Quad was built with a slightly expensive frame of about 310g (no battery), but I think it would be the same if I removed the LEDs and shark fins, but it's more than double the cost It's also 4S/1500mAh and a little 3 minutes From there, I'm flying a little 3 minutes in 4S/850mAh, so I think I've got a pretty good quad.(^-^)

It's cheap! However, the construction is not even chamfered, let alone cross-section treatment, hands are stained black (laughs) Lightweight and plenty of space (^-^) The standoff is 20mm and there is about 27.5mm space on the arm and the arm fixing plate There is no side plate for the camera, and the camera is placed on the standoff TPU part Standoff can be replaced for installation with TPU parts It's also easy to make a low-rider version even if you don't have enough stock-sized space (^-^) Recommended frame for those who like processing (^-^) I'm not sure if the arm is sold separately It's a cheap frame kit, so it's good to buy the whole kit and make it a spare part? (^-^) Recommended (^-^)

安いです！ ただ造りはそれなりで断面処理はおろか面取りすらされておらず 手が黒く汚れます(笑) 軽量でスペースも十分です(^-^) スタンドオフが20mmで アームとアーム固定用のプレートの上にスタンドオフの構造なので27.5mm程のスペースがあります カメラ用のサイドプレートはなくスタンドオフに取り付けたTPUパーツにカメラを設置します TPUパーツによる取り付けのためスタンドオフの交換は可能です ストックサイズのスペースで足りなくても ローライダー仕様にするのも作業は簡単です(^-^) 加工が好きな方にはオススメのフレームです(^-^) 別売のアーム等が販売されてるか不明ですが 安いフレームキットなのでまるごと購入しスペアパーツにできるのがいいとこですかね？(^-^) おすすめです(^-^)

It's cheap! However, the construction is not even chamfered, let alone cross-section treatment, hands are stained black (laughs) Lightweight and plenty of space (^-^) The standoff is 20mm and there is about 27.5mm space on the arm and the arm fixing plate There is no side plate for the camera, and the camera is placed on the standoff TPU part Standoff can be replaced for installation with TPU parts It's also easy to make a low-rider version even if you don't have enough stock-sized space (^-^) Recommended frame for those who like processing (^-^) I'm not sure if the arm is sold separately It's a cheap frame kit, so it's good to buy the whole kit and make it a spare part? (^-^) Recommended (^-^)

Me sorprendió mucho este frame, buena calidad, los bordes un poco afilados, pero no hay problema livianísimo, se puede montar una FC 30x30 o 20x20, tiene buena maniobrabilidad. Los brazos son de 6mm, muy durables. Precio favorable. Recomendado

Me sorprendió mucho este frame, buena calidad, los bordes un poco afilados, pero no hay problema livianísimo, se puede montar una FC 30x30 o 20x20, tiene buena maniobrabilidad. Los brazos son de 6mm, muy durables. Precio favorable. Recomendado

Me sorprendió mucho este frame, buena calidad, los bordes un poco afilados, pero no hay problema livianísimo, se puede montar una FC 30x30 o 20x20, tiene buena maniobrabilidad. Los brazos son de 6mm, muy durables. Precio favorable. Recomendado

I do like this frame alot. Compact but still enough space for everything to fit easily. Great mounts for the camera too! Cant comment on durability yet.

I do like this frame alot. Compact but still enough space for everything to fit easily. Great mounts for the camera too! Cant comment on durability yet.

I do like this frame alot. Compact but still enough space for everything to fit easily. Great mounts for the camera too! Cant comment on durability yet.

Fast delivery

Fast delivery

Fast delivery

nickel , bras un peu fragile quand meme , sinon belle frame

nickel , bras un peu fragile quand meme , sinon belle frame

nickel , bras un peu fragile quand meme , sinon belle frame

Bonne frame , bras fragile par contre

Bonne frame , bras fragile par contre

Bonne frame , bras fragile par contre

Great frame !

Great frame !

Great frame !

Amazing frame !

Amazing frame !

Amazing frame !

Nice

Nice

Nice