Customer Reviews

4.9 out of 5
Write a Review
  • All Reviews (78)
  • Image (8)
  • Video (0)
  • All Star
    • All Star(78)
    • 5 Star(71)
    • 4 Star(6)
    • 3 Star(1)
    • 2 Star(0)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (Indonesia)
  • August-31 2020 00:00:00

    works well. the extra drive gear is tearing up the aluminum. I put some grease between the gear and the arm. ended 3 pro

    Comments (1)
  • April-24 2020 00:00:00

    Installed it on my old Vertex K8400. No prints perfomed so far, but looks nice and seems to grab the filament properly.

    Comments
  • June-10 2020 00:00:00

    Good extruder but BMG like type for the same price is more reliable. Thank you.

    Comments
  • July-07 2020 00:00:00

    Packing with risk of product loss and breakage.

    Comments
  • July-04 2020 00:00:00

    Work great, you'll probaly needa YouTube videoti guide installation

    Comments
  • February-21 2020 00:00:00

    /! Pas de notice d'installation fournie /! Semble être un bon produit. Dommage qu'il soit arrivé avec quelques marques (voir photos). Le ressort est trop abîmé à mon goût, je vais donc le remplacer avec un de ceux que j'ai en stock.

    Comments
  • November-20 2019 00:00:00

    Kit estrusore (senza motore) per Creality CR10S pro, perfettamente identico a quello in dotazione. Ottimo per fare esperimenti o come parte di ricambio. Arrivato in tempi rapidi (circa 10gg). Venditore serio, consigliato.

    Comments
  • January-17 2020 00:00:00

    very nice

    Comments
  • September-23 2020 00:00:00

    Everything i ordered came other than the two plastic bushings with the metal rollers, they might of updated the design and just not of updated the image. Didn't seem to get use for them anywhere. Looks good doesn't seem like anything is damaged. It's definitely metal, feels heavy and clingy. Mounted it to the Ender 3 Pro from Creality and fits perfectly. I tried holding it back with my fingers and the filament just keeps going in. So it does work. Really good tension on the spring don't think that's going to be an issue. Keep in mind you do need to calibrate your extruder. I had my stock calibrated and it was only a couple mm off in steps. Here i was 28.45mm off in steps, so 28.45 mm under extrusion. This is due to the gearing. Perfectly normal. I'm rating it 4 stars because it's not tested long term. If it works well it would be five. Happy Printing :)

    Comments
  • August-03 2020 00:00:00

    High quality. Good finish. This is the only 'clone' or 'model' or 'type' which has a sharp filament inlet on the printer side!!! All other 'clones' or 'models' might look exactly the same, but if you pay close attention they all have a much more flattened inlet. The (slight) advantage you have with this model is that flexible filament has a smaller change to buckle up on the inlet. It might be a very very very small difference, but the difference is there and can make or break your experience. In short: don't buy other models or clones, buy this one!

    Comments
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • Rp178,042.31
    • Rp91,242.98
    • Rp70,061.57
    • Rp214,628.37
    • Rp76,727.05
    • Rp152,565.37
    • Rp73,172.13
    • Rp75,690.20
    • Rp236,846.63
    • Rp429,404.87
    • Rp2,799,500.53
    • Rp3,243,865.70
    • Rp3,836,352.58
    • Rp6,650,665.29
    • Rp313,869.93
    • Rp4,132,596.02
    • Rp151,972.89
    • Rp111,239.41