i think ít good for me

i think ít good for me

i think ít good for me

Lovely charger, can charge from a few different sources, very easy to use, beauty of this take it to the flying site and charge up from another lipo, works well and great price

Lovely charger, can charge from a few different sources, very easy to use, beauty of this take it to the flying site and charge up from another lipo, works well and great price

Lovely charger, can charge from a few different sources, very easy to use, beauty of this take it to the flying site and charge up from another lipo, works well and great price

YOU MUST CALIBRATE or RISK OF FIRE!!!! My charger had voltage measurement 0.4v too low! This could cause LIPO FIRE due to over charging. Once calibrated, the charger works well and has great features in a small size. To calibrate, get your multimeter and measure each cell of a battery. Then connect power to input while tapping 'square' button repeatedly. This will enter calibration screen. Connect the battery you measured balance port, and then change the values until they match your measurements. Also, check the input and output calibrations.

YOU MUST CALIBRATE or RISK OF FIRE!!!! My charger had voltage measurement 0.4v too low! This could cause LIPO FIRE due to over charging. Once calibrated, the charger works well and has great features in a small size. To calibrate, get your multimeter and measure each cell of a battery. Then connect power to input while tapping 'square' button repeatedly. This will enter calibration screen. Connect the battery you measured balance port, and then change the values until they match your measurements. Also, check the input and output calibrations.

YOU MUST CALIBRATE or RISK OF FIRE!!!! My charger had voltage measurement 0.4v too low! This could cause LIPO FIRE due to over charging. Once calibrated, the charger works well and has great features in a small size. To calibrate, get your multimeter and measure each cell of a battery. Then connect power to input while tapping 'square' button repeatedly. This will enter calibration screen. Connect the battery you measured balance port, and then change the values until they match your measurements. Also, check the input and output calibrations.

Sehr klein und funktionell, genau das richtige fürs Feld! Sogar Menü in deutsch ist vorhanden.

Sehr klein und funktionell, genau das richtige fürs Feld! Sogar Menü in deutsch ist vorhanden.

Sehr klein und funktionell, genau das richtige fürs Feld! Sogar Menü in deutsch ist vorhanden.

It's not bad charging, it's all in the description, YouTube is full of reviews. But. I noticed a bad glitch in the last firmware. Decided to try rocking chinese lipo accams. In the discharge mode the situation was that on one jar there were 3.3 volts, and on the other two already 3.2v. I originally set the lower limit as 3.2v. Logically, he would have to reload the first jar and keep the other two at 3.2c. But it didn't happen, the charger continued to discharge those cans below the specified level. This time I noticed such a joint, and here for the first time I looked and when I noticed, on two cans was 1.75v each. It's pptz. The most offensive thing is that at the level of iron this charger is made perfectly, small, comfortable. But this bug in the software is a very big joint. It would be nice to inform the manufacturer of this so that they correct the firmware. In general, it works, but it's better not to leave it unattended. In the mode the charge of the joints is not detected, reaches up to 4.2v and then drops the amperes and keeps the banks at this level. And yes, the most important thing. OBLIGATION: Once unpacked, calibrate the output and input voltages to the multimeter. It's not built from the factory, so you can set fire in your hut.

В целом неплохая зарядка, все как в описании, на Ютубе полно обзоров. НО. Я заметил в последней прошивке такой неприятный глюк. Решил попробовать раскачать китайские аккумы lipo. В режиме разряда получилась ситуация, что на одной банке было 3,3 вольта, а на двух других уже 3,2в. Изначально я задал нижний предел как 3,2в. По логике он должен был бы доразрядить первую банку, а две другие подержать на уровне 3,2в. Но этого не случилось, зарядник продолжил разряжать те банки ниже указанного уровня. В этот раз я заметил такой косяк, а вот в первый раз просмотрел и когда заметил, на двух банках было по 1,75в. Это ж ппц. Самое обидное, что на уровне железа этот зарядник сделан отлично, маленький, удобный. Но вот этот баг в софте - это очень большой косяк. Было бы неплохо как- то сообщить об этом производителю чтобы они поправили прошивку. В целом, работает, но лучше ее без присмотра не оставлять. В режиме заряда косяков не обнаружил, доходит до 4,2в и потом сбрасывает амперы и удерживает банки на этом уровне. И да, самое главное. ОБЯЗАТЕЛЬНО сразу после распаковки откалибруйте выходное и входное напряжение по мультиметру. С завода он не отстроен и можно устроить у себя в хате пожар.

It's not bad charging, it's all in the description, YouTube is full of reviews. But. I noticed a bad glitch in the last firmware. Decided to try rocking chinese lipo accams. In the discharge mode the situation was that on one jar there were 3.3 volts, and on the other two already 3.2v. I originally set the lower limit as 3.2v. Logically, he would have to reload the first jar and keep the other two at 3.2c. But it didn't happen, the charger continued to discharge those cans below the specified level. This time I noticed such a joint, and here for the first time I looked and when I noticed, on two cans was 1.75v each. It's pptz. The most offensive thing is that at the level of iron this charger is made perfectly, small, comfortable. But this bug in the software is a very big joint. It would be nice to inform the manufacturer of this so that they correct the firmware. In general, it works, but it's better not to leave it unattended. In the mode the charge of the joints is not detected, reaches up to 4.2v and then drops the amperes and keeps the banks at this level. And yes, the most important thing. OBLIGATION: Once unpacked, calibrate the output and input voltages to the multimeter. It's not built from the factory, so you can set fire in your hut.

The goods arrived relatively quickly 29 days, very long waited for shipment more than a month. The goods are very happy, not big weight and size is the most to carry in a pocket. The transport package is a simple package, but the box itself is very junk. The menu is very intuitive even without knowledge of English. I recommend!!!

Товар пришло сравнительно быстро 29 дней, очень долго ждал отправку больше месяца. Товаром очень доволен, не большой вес и размер самое то чтоб носить в кармане. Транспортеровочная упаковка простой пакет, но сама коробка очень жосткая. Меню очень интуитивно понятно даже без знания английского. Рекомендую !!!

The goods arrived relatively quickly 29 days, very long waited for shipment more than a month. The goods are very happy, not big weight and size is the most to carry in a pocket. The transport package is a simple package, but the box itself is very junk. The menu is very intuitive even without knowledge of English. I recommend!!!

Excellent Charger for beginners! It has all the functions as specified we can save upto 3 charge profiles for li-poly, li-ion, LiHV, NiMh and lead acid. can connect 1S to 6S lipo. It has storage function which you could manually set the storage vtg. Max power handling is 150watts and an output current limit of 10A. the input power has a limit of 7V to 28V and has a current limit of 12A. has Discharge function where you could either discharge internally, externally, or by recycling (dumping charge back to source if the source itself is a battery) The charger has an inbuilt fan for cooling..it starts working at 45degree and run at max power at set temperature which u could adjust in the settings. But i mainly bought this over ISDT is that it can measure or output PWM, PPM, Sbus signals..you have a 3pin for that on the left side of the charger. the M6 can also measure internal resistance and can balance cells for upto 6s batteries. On the output section we could choose the charger to work as a Power supply, where we could set the voltage from 1 to 28V and current to 0.5 to 10A... Although, the over current protection is slow to kick in. The system has an inbuilt fuse..if u short the output, you can change the smd fuse. (on the ISDT chargers they have poly fuses..means that the fuse will not be permanently damaged when a short occurs). It has a 5V 2.1A USB port. it can be used to charge your phone. or upgrade the M6 firmware (the latest firmware is 1.22). updating firmware is so easy..just plug in the USB cable which came with the charger download the latest firmware from toolkitRc's site, extract the zip files and just run the windows batch file.. And for some of you..u may need to calibrate the device.. for that press the exit button while you plug in the input supply. then you will be taken to a screen where you could change the values. plug in a battery of known voltage and check the vtg on the charger and adjust it accordingly. (refer my review pics)

Excellent Charger for beginners! It has all the functions as specified we can save upto 3 charge profiles for li-poly, li-ion, LiHV, NiMh and lead acid. can connect 1S to 6S lipo. It has storage function which you could manually set the storage vtg. Max power handling is 150watts and an output current limit of 10A. the input power has a limit of 7V to 28V and has a current limit of 12A. has Discharge function where you could either discharge internally, externally, or by recycling (dumping charge back to source if the source itself is a battery) The charger has an inbuilt fan for cooling..it starts working at 45degree and run at max power at set temperature which u could adjust in the settings. But i mainly bought this over ISDT is that it can measure or output PWM, PPM, Sbus signals..you have a 3pin for that on the left side of the charger. the M6 can also measure internal resistance and can balance cells for upto 6s batteries. On the output section we could choose the charger to work as a Power supply, where we could set the voltage from 1 to 28V and current to 0.5 to 10A... Although, the over current protection is slow to kick in. The system has an inbuilt fuse..if u short the output, you can change the smd fuse. (on the ISDT chargers they have poly fuses..means that the fuse will not be permanently damaged when a short occurs). It has a 5V 2.1A USB port. it can be used to charge your phone. or upgrade the M6 firmware (the latest firmware is 1.22). updating firmware is so easy..just plug in the USB cable which came with the charger download the latest firmware from toolkitRc's site, extract the zip files and just run the windows batch file.. And for some of you..u may need to calibrate the device.. for that press the exit button while you plug in the input supply. then you will be taken to a screen where you could change the values. plug in a battery of known voltage and check the vtg on the charger and adjust it accordingly. (refer my review pics)

Excellent Charger for beginners! It has all the functions as specified we can save upto 3 charge profiles for li-poly, li-ion, LiHV, NiMh and lead acid. can connect 1S to 6S lipo. It has storage function which you could manually set the storage vtg. Max power handling is 150watts and an output current limit of 10A. the input power has a limit of 7V to 28V and has a current limit of 12A. has Discharge function where you could either discharge internally, externally, or by recycling (dumping charge back to source if the source itself is a battery) The charger has an inbuilt fan for cooling..it starts working at 45degree and run at max power at set temperature which u could adjust in the settings. But i mainly bought this over ISDT is that it can measure or output PWM, PPM, Sbus signals..you have a 3pin for that on the left side of the charger. the M6 can also measure internal resistance and can balance cells for upto 6s batteries. On the output section we could choose the charger to work as a Power supply, where we could set the voltage from 1 to 28V and current to 0.5 to 10A... Although, the over current protection is slow to kick in. The system has an inbuilt fuse..if u short the output, you can change the smd fuse. (on the ISDT chargers they have poly fuses..means that the fuse will not be permanently damaged when a short occurs). It has a 5V 2.1A USB port. it can be used to charge your phone. or upgrade the M6 firmware (the latest firmware is 1.22). updating firmware is so easy..just plug in the USB cable which came with the charger download the latest firmware from toolkitRc's site, extract the zip files and just run the windows batch file.. And for some of you..u may need to calibrate the device.. for that press the exit button while you plug in the input supply. then you will be taken to a screen where you could change the values. plug in a battery of known voltage and check the vtg on the charger and adjust it accordingly. (refer my review pics)

Almost everything ok except fingerprints under screen. Thia cannot be cleaned without open the charger.

Almost everything ok except fingerprints under screen. Thia cannot be cleaned without open the charger.

Almost everything ok except fingerprints under screen. Thia cannot be cleaned without open the charger.

Thanks banggood :)

Thanks banggood :)

Thanks banggood :)

I recommend this charger, it has excellent balance, it is quite intuitive, it gives a lot of battery information, it can be used to know the status of your battery without having to plug it into the power supply, it has a small size that makes it very portable, it comes with a screen saver, you can use it with a lipo to load a usb, I just give it a bug that I lower the note, among the languages there is no Spanish, includes Chinese, English, French, Italian and Portuguese, there is only one language that includes being spoken more than Spanish, why not include it?

Recomiendo este cargador, tiene un excelente balanceo, es bastante intuitivo, da mucha información de la batería, se puede usar para saber el estado de tu batería sin tener que enchufarlo a la fuente de alimentación, tiene un tamaño pequeño que lo hace muy portátil, viene con un protector de pantalla, puedes usarlo con una lipo para cargar un usb,solo le pongo un fallo por el que le bajo la nota, entre los idiomas no está el español, incluye chino, ingles, francés, italiano y portugués, solo hay un idioma de los que incluye que se hable más que el español, por qué no incluirlo?

I recommend this charger, it has excellent balance, it is quite intuitive, it gives a lot of battery information, it can be used to know the status of your battery without having to plug it into the power supply, it has a small size that makes it very portable, it comes with a screen saver, you can use it with a lipo to load a usb, I just give it a bug that I lower the note, among the languages there is no Spanish, includes Chinese, English, French, Italian and Portuguese, there is only one language that includes being spoken more than Spanish, why not include it?