gipsyblues
Q: WHAT IS THE PIN OUT DESCRIPTION OF THE YELLOW 8 PIN BLOCK ON THIS BOARD?
Asked by gipsyblues on 2020-01-03 04:17:58
Creat the pinout fits directly onto an ESP-01 or ESP-01s, it's just plugged in there. Add power (5V) to this board, and the ESP also gets the power it needs (3.3v, regulator is on this board). Ignore the answer that says you need a cable, it's nonsense.
2021-11-01 03:36:18 Helpful (0)Q: what battery is suggested for use with this device? Is it for internal or external use
Asked by gipsyblues on 2021-04-03 09:08:42
Yogurt Use a lithium battery, which can be placed inside the case, but note that the battery size should be smaller than the case size
2021-04-08 02:09:20 Helpful (0)
Lupar https://github.com/Xinyuan-LilyGO/LilyGO-T-Beam
2020-03-03 02:12:33 Helpful (1)
gipsyblues This dialogue box does not allow the entry of URLs.For the datasheet, please go to the website of espressif and search for esp32_datasheet_en.pdf under documentation
2020-06-06 09:28:13 Helpful (1)
gipsyblues Go to the ftdichip website. Add a dot com to the name of the chip. Go to support and find documents Under Documents search for install Guides for mac osx. Look for FT232. If the chip is genuine the mac driver listed there should work!
2020-05-04 02:29:28 Helpful (0)
sam1301 I’m not sure there is a blink sketch to blink the blue LED as it’s actually linked to the AXP charge chip and not the ESP32 chip. It may be possible if you can instruct the AXP chip to turn on and off the LED but it usually comes on by itself when charging a battery.
2020-03-22 03:02:40 Helpful (0)
gipsyblues Jelbert, could you please confirm which demo software blinks th LED(the one that comes on during the battery charging. I could not get the LED to flash
gipsyblues quite expensive? this board is the best price performance features board on the market for now!
Q: Does anyone have a link to install the drivers. I'm not sure what to search online. Thanks
Asked by awaiskhawaja2003 on 2020-02-05 04:48:45
gipsyblues Yes, I definitely do However Bangwood does not allow the inclusion of a website URL in their response dialog box The driver you are looking for is the CP210x USB to UART Bridge VCP Drivers, from Silicon Labs. Please Google that info and am sure you will find the URL Don't know if they allow email addresses either. will try to add an email address you could contact and I would be happy jason.robertsiii@gmail.com
2020-02-05 06:41:56 Helpful (1)Q: sdk?
Asked by exquisitus on 2019-11-26 05:26:44
gipsyblues Please see github for Heltec Cubecell series and wasn of eu for top flight beyond sdk software
2020-01-30 10:17:27 Helpful (0)
Q: what thread type is this nozzle, I am looking for an NPT thread type
Asked by gipsyblues on 2019-09-23 07:12:25
Bakulesh this one is not NPT thread type. it is straight one
2019-09-24 01:04:52 Helpful (0)We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
dmeagor I needed to use the V1 board settings to get it to upload in Arduino IDE so I'm guessing its V1.
2020-06-01 05:16:25 Helpful (0)