All Messages

Q: what size is the prop hub shaft? 5mm? 6mm?

Asked by Andy0679 on 2021-08-08 05:43:55

Wes The PNP kit I received included SunnySky X2216-7 and 1400KV with 5mm shaft

2021-08-08 06:35:46 Helpful (2)
Submit
Answers (6)

Q: What voltage are the PNP servos rated for?

Asked by WillF on 2021-06-14 05:27:21

Wes The spare part is available for AR Wing Pro and the spec sheet says 4.8 to 6V DC.

2021-06-14 06:21:08 Helpful (1)
Submit
Answers (3)

Wes The manual for F405-Wing shows use UART2-RX RX2 pad for IBUS, PPM etc., instead of Sbs pad which is for SBUS.

2021-04-25 09:07:33 Helpful (0)
Submit
Answers (2)

Wes I tested it on servo tester and it sweeped 180 deg. like normal proportional servo. Instructions say to increase pulse width to obtain 270 degrees. I haven't tried that yet, but I expect it will work as advertised.

2021-02-24 04:18:55 Helpful (1)
Submit
Answers (1)

Wes It says .01 minimum illumination at 1.2F so you need something like .0001 or .00001 like night eagle II or cat 2 starlight for night. The night eagle II is black and white only but it is the best one for night vision.

2021-02-06 01:29:03 Helpful (1)
Submit
Answers (4)

Q: hi what are the sizes of the battery width, height, length

Asked by JGsnr on 2020-11-13 03:17:02

Wes I get about 2 and seven eighths

2020-11-13 04:07:48 Helpful (0)
Submit
Answers (1)

Q: how do i set rth failsafe for flysky ppm reciever??

Asked by 360noscopy on 2020-08-11 08:38:59

Wes Check what channel you assigned in the Owl's setup menu to be RTH first. Once you setup the flight controller and got the mode and sub-mode switches set you can verify in your OSD which switch or switch combination activates RTH. Then you can go into System -> RX Setup -> Failsafe and set the mode switch channel and sub-mode switch channel (if you setup a sub-mode switch) to the values that select the proper switch position(s). For example on mine I have channel 5 mode switch with manual, stabilized, and sub-mode, then I have channel 6 set to althold, circle, rth. So if -100% is where sub-mode is on channel 5, and -100% is where RTH is on channel 6, then I can set just those channels to -100% and then press the cancel button on my FlySky TX to save those settings. To verify I can power up the TX and plane and see it's all working in the OSD, then turn off the TX and if it's working the plane (Owl flight controller) will go into RTH. Only change the channels which activate RTH, don't for example set the throttle to -100% because the RTH will control that. SAFETY NOTE: You should always remove your propeller when testing in case it powers up by some error to avoid serious injury.

2020-08-11 09:36:33 Helpful (1)
Submit
Answers (1)

Q: Does it come with ZOHD Kopilot?

Asked by BG231341021 on 2020-07-24 12:09:11

Wes Order the FPV Version to get the ZOHD Kopilot Lite and VC400 All in one Camera included. You will have everything you need to fly FPV, but you must provide your own battery, rc receiver, and rc transmitter, as well as some kind of FPV goggles or monitor.

2020-07-24 12:31:37 Helpful (2)
Submit
Answers (3)

Q: Do you have the channel list for the vtx and Rx?

Asked by folatoye on 2019-01-10 11:55:41

Wes The800mW TX is listed in the description as frequency. The Receiver Channels: CH0 0.910G CH1 0.980G CH2 1.010G CH3 1.040G CH4 1.080G CH5 1.120G CH6 1.160G CH7 1.200G CH8 1.240G CH9 1.280G CH10 1.320G CH11 1.360G

2020-07-22 07:51:37 Helpful (0)
Submit
Answers (1)

Wes Youneed a multiprotocol module for example I use KN --> WlToys protocol for this model on my Jumper T8SG V2 Advanced radio.

2020-07-02 09:07:52 Helpful (0)
Submit
Answers (2)

Wes Youselect LH or RH to match your VTX antenna (RHCP TX to RHCP RX or LHCP TX to LHCP RX). Each port on the screen is an independant RX so you can put it in either connector. The best way to use this "diversity receiver" setup is a directional "beam" type in one, and an omni-directional antenna in the other. The beam type must be pointed at your craft TX antenna, and the omni-directional will work in basically all directions (all antennas do have some small null areas to keep in mind).

2020-07-02 09:03:09 Helpful (0)
Submit
Answers (1)