excellent receiver , once flashed with new firmware Flashing details:- http://www.banggood.com/USBASP-USBISP-3_3-5V-AVR-Downloader-Programmer-With-ATMEGA8-ATMEGA128-p-934425.html http://www.rcgroups.com/forums/showpost.php?p=32959023&postcount=1147 http://www.rcgroups.com/forums/showpost.php?p=32382264&postcount=864 CH5-MOSI CH6-MISO CH7-SCK VCC GND RESET ( attach before plugging in usbasp) Programable fail-safe (PFS) and binding of RX-F802:- 1) Press bind button on RX and power it up , release button . Led will stay on 2) Turn on Taranis :- press menu button and then page button . Scroll down and set mode=d8 and channel range =Ch1-8. Then enter bind . 3) RX led will go off 4) Arrange sticks for your preferred fail safe 5) Press ENT button on Taranis to exit bind 6) RX will flash 7) Remove power to receiver and re- connect , it should come on with a solid led 8) Your done , receiver bound and fail-safe set PPM out:- connect channels 1+3 , PPM out will be on channel 4 Sbus out:- Connect channels 5+7 . Sbus is on tx pad under rx cover next to Ariel RSSI ( signal strength) :- RSSI is output on Channel 5 when in SBUS or PPM mode for most firmwares. It can be put on channel 9 when the cleanflight software is loaded For MWOSD the min rssi should be set to 33 and the max to 100

excellent receiver , once flashed with new firmware Flashing details:- http://www.banggood.com/USBASP-USBISP-3_3-5V-AVR-Downloader-Programmer-With-ATMEGA8-ATMEGA128-p-934425.html http://www.rcgroups.com/forums/showpost.php?p=32959023&postcount=1147 http://www.rcgroups.com/forums/showpost.php?p=32382264&postcount=864 CH5-MOSI CH6-MISO CH7-SCK VCC GND RESET ( attach before plugging in usbasp) Programable fail-safe (PFS) and binding of RX-F802:- 1) Press bind button on RX and power it up , release button . Led will stay on 2) Turn on Taranis :- press menu button and then page button . Scroll down and set mode=d8 and channel range =Ch1-8. Then enter bind . 3) RX led will go off 4) Arrange sticks for your preferred fail safe 5) Press ENT button on Taranis to exit bind 6) RX will flash 7) Remove power to receiver and re- connect , it should come on with a solid led 8) Your done , receiver bound and fail-safe set PPM out:- connect channels 1+3 , PPM out will be on channel 4 Sbus out:- Connect channels 5+7 . Sbus is on tx pad under rx cover next to Ariel RSSI ( signal strength) :- RSSI is output on Channel 5 when in SBUS or PPM mode for most firmwares. It can be put on channel 9 when the cleanflight software is loaded For MWOSD the min rssi should be set to 33 and the max to 100

excellent receiver , once flashed with new firmware Flashing details:- http://www.banggood.com/USBASP-USBISP-3_3-5V-AVR-Downloader-Programmer-With-ATMEGA8-ATMEGA128-p-934425.html http://www.rcgroups.com/forums/showpost.php?p=32959023&postcount=1147 http://www.rcgroups.com/forums/showpost.php?p=32382264&postcount=864 CH5-MOSI CH6-MISO CH7-SCK VCC GND RESET ( attach before plugging in usbasp) Programable fail-safe (PFS) and binding of RX-F802:- 1) Press bind button on RX and power it up , release button . Led will stay on 2) Turn on Taranis :- press menu button and then page button . Scroll down and set mode=d8 and channel range =Ch1-8. Then enter bind . 3) RX led will go off 4) Arrange sticks for your preferred fail safe 5) Press ENT button on Taranis to exit bind 6) RX will flash 7) Remove power to receiver and re- connect , it should come on with a solid led 8) Your done , receiver bound and fail-safe set PPM out:- connect channels 1+3 , PPM out will be on channel 4 Sbus out:- Connect channels 5+7 . Sbus is on tx pad under rx cover next to Ariel RSSI ( signal strength) :- RSSI is output on Channel 5 when in SBUS or PPM mode for most firmwares. It can be put on channel 9 when the cleanflight software is loaded For MWOSD the min rssi should be set to 33 and the max to 100

Nice little rx, lightweight, small, e.g. half height of a R615X. Hence this one will fit even on small frame. For the A1&A2 ports, it comes with two bread board cables. The antenna is a dipole antenna, but I am wondering why most Chinese builders of that stuff stay below 1/4 wave for the length on the active part.. After I have done the mod on the 7e for this rx, I will report how the telemetry works.

Nice little rx, lightweight, small, e.g. half height of a R615X. Hence this one will fit even on small frame. For the A1&A2 ports, it comes with two bread board cables. The antenna is a dipole antenna, but I am wondering why most Chinese builders of that stuff stay below 1/4 wave for the length on the active part.. After I have done the mod on the 7e for this rx, I will report how the telemetry works.

Nice little rx, lightweight, small, e.g. half height of a R615X. Hence this one will fit even on small frame. For the A1&A2 ports, it comes with two bread board cables. The antenna is a dipole antenna, but I am wondering why most Chinese builders of that stuff stay below 1/4 wave for the length on the active part.. After I have done the mod on the 7e for this rx, I will report how the telemetry works.

Athough only single antenna it is pa/LNA and dipole antenna , new fw is available search diy frsky RX , a guy called Midelic has written the code for this, also his code now Inc!uded all CH failsafe and s.bus and fast reconnect if signal lost. More to come may include more telemetry like altimeter.

Athough only single antenna it is pa/LNA and dipole antenna , new fw is available search diy frsky RX , a guy called Midelic has written the code for this, also his code now Inc!uded all CH failsafe and s.bus and fast reconnect if signal lost. More to come may include more telemetry like altimeter.

Athough only single antenna it is pa/LNA and dipole antenna , new fw is available search diy frsky RX , a guy called Midelic has written the code for this, also his code now Inc!uded all CH failsafe and s.bus and fast reconnect if signal lost. More to come may include more telemetry like altimeter.

Ideal receiver to use on planes, helis, multicopters or flying wings. I am using it on a FPV flying wing and works great. On my Taranis I have the telemetry for RSSI and Battery voltage, just what I looking for. The real advantage it's that don't need any voltage divider, just plug from the balance plug of my 3S lipo battery to the receiver A1 port and get the value. Just perfect.

Ideal receiver to use on planes, helis, multicopters or flying wings. I am using it on a FPV flying wing and works great. On my Taranis I have the telemetry for RSSI and Battery voltage, just what I looking for. The real advantage it's that don't need any voltage divider, just plug from the balance plug of my 3S lipo battery to the receiver A1 port and get the value. Just perfect.

Ideal receiver to use on planes, helis, multicopters or flying wings. I am using it on a FPV flying wing and works great. On my Taranis I have the telemetry for RSSI and Battery voltage, just what I looking for. The real advantage it's that don't need any voltage divider, just plug from the balance plug of my 3S lipo battery to the receiver A1 port and get the value. Just perfect.

rock solid performance updating guide here: http://nathan.vertile.com/blog/2016/02/09/airwolf-diy-frsky-rx-sbus

rock solid performance updating guide here: http://nathan.vertile.com/blog/2016/02/09/airwolf-diy-frsky-rx-sbus

rock solid performance updating guide here: http://nathan.vertile.com/blog/2016/02/09/airwolf-diy-frsky-rx-sbus

Satisfied, binded to 1.x, full 7 channels to use 1 binding, In Taranise plus after plugging the cable with service battery cable transmits the status of the battery max 3s to the receiver in section - A1. Best price on 7 channel - satisfaction. Google trans: Satisfied, complete to 1.x, full 7 months for use 1 month, in Taranis plus after the service of the operator used it again with the highest status max 3s to the operator in connection - A1. The best price for channel 7 - destination.

Spokojný, nabindované na 1.x, plných 7 kanálov k použitiu + 1 bindovací, v Taranise plus po zapojení káblika + so servis kábla batérie prenáša stav baterie max 3s do prijímača v sekcii - A1. Najlepšia cena na 7 kanál - spokojnosť. Google trans: Satisfied, connected to 1.x, full 7 channels for use + 1 binding, in Taranis plus after connecting the cable + with the service of the battery cable it transmits the battery status max 3s to the receiver in section - A1. The best price for channel 7 - satisfaction.

Satisfied, binded to 1.x, full 7 channels to use 1 binding, In Taranise plus after plugging the cable with service battery cable transmits the status of the battery max 3s to the receiver in section - A1. Best price on 7 channel - satisfaction. Google trans: Satisfied, complete to 1.x, full 7 months for use 1 month, in Taranis plus after the service of the operator used it again with the highest status max 3s to the operator in connection - A1. The best price for channel 7 - destination.

Telemetry and control confirmed, not had the weather for flying yet but this is a great cheap receiver. No reason not to trust it.

Telemetry and control confirmed, not had the weather for flying yet but this is a great cheap receiver. No reason not to trust it.

Telemetry and control confirmed, not had the weather for flying yet but this is a great cheap receiver. No reason not to trust it.

not sure about the range with single non diversity antenna but works ok for ~500m - using it with a trainer with a lot of functions(lights, telemetry etc). To update firmware you need an avt usbasp programmer , remove the case and there is a RESET pad for programming.

not sure about the range with single non diversity antenna but works ok for ~500m - using it with a trainer with a lot of functions(lights, telemetry etc). To update firmware you need an avt usbasp programmer , remove the case and there is a RESET pad for programming.

not sure about the range with single non diversity antenna but works ok for ~500m - using it with a trainer with a lot of functions(lights, telemetry etc). To update firmware you need an avt usbasp programmer , remove the case and there is a RESET pad for programming.

Projet maintenu par Midelic sur rcgroups : http://www.rcgroups.com/forums/showthread.php?t=2124647 De nouvelles fonctionnalités sont ajoutées régulièrement. Récemment le Failsafe et le S-BUS.

Projet maintenu par Midelic sur rcgroups : http://www.rcgroups.com/forums/showthread.php?t=2124647 De nouvelles fonctionnalités sont ajoutées régulièrement. Récemment le Failsafe et le S-BUS.

Projet maintenu par Midelic sur rcgroups : http://www.rcgroups.com/forums/showthread.php?t=2124647 De nouvelles fonctionnalités sont ajoutées régulièrement. Récemment le Failsafe et le S-BUS.

When I received the RX, I found out that it was only 7channels. Also, it has no bind button. Have to use strap for binding. A complaint has been raised with Banggood.

When I received the RX, I found out that it was only 7channels. Also, it has no bind button. Have to use strap for binding. A complaint has been raised with Banggood.

When I received the RX, I found out that it was only 7channels. Also, it has no bind button. Have to use strap for binding. A complaint has been raised with Banggood.