Customer Reviews

4.58 out of 5
Write a Review
  • All Reviews (26)
  • Image (1)
  • Video (1)
  • All Star
    • All Star(26)
    • 5 Star(19)
    • 4 Star(4)
    • 3 Star(2)
    • 2 Star(1)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (Indonesia)
|
Show Original

A part of the review has been auto-translated.

  • 12/11/2017

    Perfect board with many features. Original software has no LED-Strap function. Please install the latest software first.

    Comments
    Show Original
  • 18/09/2020

    Exactly as ordered. Everything top

    Comments
    Show Original
  • 24/08/2017

    Fastest CPU, Software has nowhere near even caught up to this FC yet. Currently the 32kHz Gyro is useless. You have to use a CLI command to even enable it and when you do if you use anything over 32kHz/8kHz the CPU is loaded to 100%. This is problem..... this CPU can easily do 32kHz/32kHz however the software just is not there yet in terms of coding. This time next year and F7 will be all the rage for real. Right now the only way to run faster than 8kHz/8kHz is with an F4. If my memory serves me correctly all F4's can do 16kHz/16kHz. Either way.... great FC and it also has a barometer which I think EVERY FC should have. Why would you ever want to fly without knowing your height?

    Comments
    Show Original
  • 20/08/2017

    This F7 board only has 3 UARTS labeled (1, 3, and 6), but Betaflight 3.2 RC3 shows UART 2 as an option, so that may be labeled as something different. Current Betaflight software does not support the 32khz gyro, but with some time to catch up I'm sure it eventually will. Right now the only supported version of Betaflight is the 3.2 Release Candidate, so there's no option for a tested and stable software version. Overall it's a good board, the current sensing and OSD work perfectly. The plug to connect to a 4-in-1 ESC allows for exceptionally compact and clean builds, and the SD card holder makes BlackBox recording easy up to 8khz (the current PID limit with the slower gyro). The only other issue I've seen is that the processor gets quite warm on the bench, but that shouldn't be an issue once it gets some airflow across it. It doesn't get hot to the touch, just a bit warm. Overall it's a great board, but being on the bleeding edge comes with its issues.

    Comments
    Show Original
  • 07/08/2017

    This board is working well in my 130 jalapura frame build. The quality seems good. I have updated it to Betaflight 3.2.0 RC3 and working fine. I have a spektrum serial telemetry receiver and it works on the various UART RX pads in spektrum 2048 mode. But I have not been able to get it to work in bidirectional serial mode with telemetry on any of the uart Tx pads. Is this is a betaflight firmware issue for the new F7 chips or if it is the board.? No Instructions to switch between gyros

    Comments
    Show Original
  • 05/09/2018

    I was expecting this to have the same pins as an F4 for some reason but they are differnt. Not sure what that means in terms of figuring out the wiring as there is minimal documentation at this stage. Plugged in flashed with iNav for an Omnibus F7 as at the time of writing there is not an F7 Pro target. Seems to work as expected in the iNav gui.

    Comments
    Show Original
  • 20/08/2018

    bueno el caso esque no va ni por ppm.solo va por ibus.y parece ser que esta mal.porlomenos esta que me llego.he provado todos los firmware para ella porque el 3.2.0 al parecer ya dava error y ningun firmware hasta la fecha soluciona el problema.ya me puse en contacto con bosotros,aver si me dais una solucion para enviarla.gracias.

    Comments
    Show Original
  • 25/08/2017

    I'm using this board for the GEPRC GEP LX Leopard. I've choosen this becasue I wanted an integrated OSD and a barometer. However, the setup was a pain. First issue was to get the latest firmware flashed because with the stock one the board is quite useless (no OSD, no gyros,...) But flashing didn't work - I had to find, install and understand the Zadig tool first in order to be able to flash this board. The second issue was to connect the receiver - there was no power. Only after I find out that there has to be a bridge soldered between the 3.3V (for Spektrum) and the 5V (for FrSky, Crossfire...) pin in order to get power to the receiver. If works nice after all, but I wouldn't have to spend hours on searching and testing if there was a better documentation for this board!

    Comments (1)
    Show Original
  • 27/01/2018

    Consegui fazer funcionar quase tudo, gps barometro, compasso. sá não consigo de forma alguma fazer funcionar meu receptor Ezuhf em ppm. Já perdi dias pesquisando, simplesmente não consigo. se alguem puder me ajudar eu agradeço

    Comments (1)
    Show Original
  • 20/11/2017

    Very good Flight controller, I ugraded firmware with Betaflight 3.2.2 and quadcopter flies very good, You have to select MPU6000 put Gyro sampling ad Looptime 8 and will fly very well, If You use ICM20608 don't fly good I think is formware issue, hope next update can fix it

    Comments
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • Rp630,125.18
    • Rp82,976.45
    • Rp742,413.17
    • Rp90,705.36
    • Rp80,059.88
    • Rp662,353.29
    • Rp728,996.94
    • Rp495,671.26
    • Rp319,947.85
    • Rp86,767.99
    • Rp2,132,450.95
    • Rp233,179.86
    • Rp71,601.82
    • Rp148,599.30
    • Rp400,007.72
    • Rp59,206.39
    • Rp837,347.56
    • Rp88,809.59