Customer Reviews

4.85 out of 5
See all 513 reviews
Write a Review
  • All Reviews (513)
  • Image (115)
  • Video (1)
  • All Star
    • All Star(513)
    • 5 Star(454)
    • 4 Star(47)
    • 3 Star(9)
    • 2 Star(2)
    • 1 Star(1)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (Lao People's Democratic Republic)
|
Show Original

A part of the review has been auto-translated.

  • 11/09/2020

    • Build quality is okey for 30$ • You maybe have to sand down the carbon edges, they can be pretty sharp. • Vista fits perfect, 20x20mm holes in the back. remember you need the longer camera cable. • Air unit doesn‘t fit, the standoffs/antennas are in the way. • The Standoffs could have abetter quality, you maybe have to deburr it. • You definitely need longer screws to mount the dji fpv cam, the stock ones are too short because the gap between the camera and the carbonplates are too big.

    Comments (5)
    Show Original
  • 05/09/2020

    supports ONLY 22mm or smaller fpv camera. frame seems sturdy. I bought two frames and all of the arms measure 4.86-4.91mm thickness. I saw a review about the press nuts not fitting in the holes well. there are not meant to. they just sit where pictured, they fit right into the groove perfectly. giving this a 4 star only because some of the edges were rough and splintery. nothing some sand paper couldn't fix.

    Comments (1)
    Show Original
  • 10/12/2021

    The arms can move laterally a few millimetres, even if the screws are tight. A 5.1 inch propeller misses or hits the rear standoff, depending on where the rear arms are sitting. Use 5 inch propeller only. The aluminium stand off has weak thread, easy to strip. I had to use longer screws. You have to take a stack screw out to change an arm. The motor arm ends are less than the diameter of the 22xx motor, so if you clip a steel post, you'll bash the bell instead of the carbon (I did this the first time I flew with this frame. destroyed a brand new motor). The four screws under the stack nearly touch the ESC so I had to grind them down with a dremel. The camera plate hole position is not suitable. I can't angle more than 20 degrees. I drilled new holes in the plates to fix this. Coming from an iflight XL5, this frame has been disappointing. Gave 4 stars because I can't complain much for the price.

    Comments (2)
    Show Original
  • 27/05/2021

    Looks Like a good fpv frame. Here is how you can build it Picture by Picture

    Comments
    Show Original
  • 03/11/2020

    Good frame, it feels strong, good work on the carbon fiber, I had to work on some details, open more holes to get the hardware in, the edges are sharp and I had to sand them, for the price seems good buy. Not the version where you can mount the DJI Air join, but if the Caddx Vista

    Comments (2)
    Show Original
  • 25/08/2020

    Blank mounting, looks robust. I'll switch to the 6s with this frame. p'tit comparo with a martian and real4 chassis (reverb clone)

    Comments
    Show Original
  • 30/11/2020

    Really great product, perfect packaging and shipping.

    Comments (2)
    Show Original
  • 30/01/2021

    shipping was quite fast - you get a lot for this price - good job BG if you order this kit you need to know that its made for a dji vista. if you want to mount an analog mini cam you will have the frame in your fov. u cant mount a micro cam its too small an if you plan to use a bracket it doesnt work. i saw already custom printed side plates but this would lower the stability. also be aware you cant quickchange a broken arm because the stack screw is blocking the arm. also the lowest point are the screws who hold the arm (2 each arm). so if you land or slide you damage the screwheads and maybe arent able to remove them after. i recomment to add skids or some protection to the screwheads. the press nuts are not really usefull, you should change them. also the screws from the arms should be replaced with fitting screws. good quality carbon and for this price you will get good starterkit for building a 5 inch quad. with the explained modification you can built a nice freestyle quad.

    Comments (2)
    Show Original
  • 15/01/2021

    Great frame for the price. They even put a little metal file in the package. I guess that was for any ruff bits of which there was none. One things I think could be improved are the length of the arms as if you use 5.1 inches props (as many are these days) they are only a whisker away from the frame at the back.

    Comments (2)
    Show Original
  • 12/01/2021

    Stable and compact frame. Has now some crashes behind him and he has survived well. problem-free with a Caddx Vista build-up bar. The screws and standoffs are unfortunately not of such good quality. Screws must be partly replaced because too short and therefore demolition risk! But for the price you can not complain:)

    Comments (4)
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • US$9.99
    • US$39.99
    • US$109.99
    • US$33.99
    • US$5.99
    • US$13.99
    • US$5.99
    • US$4.99
    • US$32.99
    • US$7.76
    • US$6.47
    • US$69.99
    • US$7.99
    • US$41.11
    • US$57.99
    • US$36.09
    • US$59.21
    • US$14.99