Best Deals for POCO X3 Pro - Banggood SEA Online Shopping

BG473457484 13/09/2020

Hello everyone, I would like to share my experience with this product that I used to replace the mainboard of one of my old led TV that I'm currently using as secondary monitor. I suggest to follow the instruction to assure the compatibility with your panel, I don't know if the provided cable is compatible with my panel, because I used the old one . Another thins that could help some is that I used my led inverter instead of the provided one, just check that your is pin to pin compatible with the board (check VCC and GND and Enable pins position(. The boards come with a factory software that was not compatible with my panel but I just used the VST53C_4MB_M.bin for my resolution, I noticed that the vendor developed specific software version for specific panel, so I suggest to check if there's a version for your panel before using the general. I was able to place all provided things inside the tv case and I like the results (you can judge, just check the uploaded photo). The job was not complicated but I checked pinout, compatibility and other stuffs a lot of time before that I decide to powered on my board, I think that if you will choose wrong panel VCC on pinout you can damage both board and panel so be careful!!! According to the audio IC datasheet I decided to leave disconnected the original audio speaker because both electrical power and impedance were not compatible (6W@4ohm for channel) , the provided IC is only 2ch for 2W@3ohm. I kindly suggest this kit if you need a cheap monitor or CCTV. I also suggest to read careful the provided manual just to prevent any damage on stuff or person. Unfortunately I have to highlight that I had some issues with shipment (the local courier delayed the delivery and bangood support cannot help me as I expected, Bangood please improve your support on after sales issue that will prevent any bad expirence), but finally after a lot of phone call I guessed the courier and I found my board. Hope this can help you guys!

T.SK105A.03 Universal LCD LED TV Controller Driver Board TV/PC/VGA/HDMI/USB+7 Key Button+2ch 6bit 30pins LVDS Cable+1 Lamp Inverter

US$18.99 US$25.99

5

Comments (2)

TOOLTOP ET-691 32*32 Portable Infrared Thermal Imager Display Resolution 320x240 Pixels Handheld Thermal Imager Infrared Camera Thermometer Digital Display Heating Detector

US$166.99 US$200.99

Q: any one used it to detect short circuit ? is it capable to detect hot spot ? (example small component overheated ?)

Asked by BG473457484 on 2021-09-17 02:59:50

BG534817441 Hello Now I have tried a closed component myself, but the solution is not large enough to see what may have burned off. Here you need to go and buy some more advanced equipment. Enjoy Greeting Svend Nielsen

2021-09-19 01:20:42 Helpful (1)

Submit

Answers (3)

BG473457484 22/05/2021

the item arrived on time (about 3 weeks after that I ordered it). To be honest this is just a first impression but I'm using it from this morning and I'm satisfied, the phone is fast and apps run fluid. the battery consumption is quite normal and depend on how you use the phone. With a 75% I was able to complete the first configuration and then make a couple of video call for about 2 hours. actually I'm very satisfied (I migrated from Samsung S5 ). the phone include a silicon cover but unfortunately no screen protector and no headphones. I also played a couple of games using my stadia account and worked very well. I'm very satisfied from my purchase I thin that is one of the best buy for this price. The phone arrived in a solid package that protected it. Thanks bangood for this !

POCO X3 Pro Global Version Snapdragon 860 8GB RAM 256GB ROM 6.67 inch 120Hz Refresh Rate 48MP Quad Camera 5160mAh Octa Core 4G Smartphone

US$279.00 US$369.99

4

Comments (0)

BG473457484 08/01/2021

I received item jus after a week so the shipment was one of the faster of ever thanks bangood!!! I just unboxed the package that come with a nice handy bag. I executed a couple of test for all function except for the AC current and the result were very well. Using a bench power supply with a lod that generates 2.36 Amps I read 2.55A without using the rel function but if I get the clamp near the wire and then select rel and now executing the measure I read 2.39A that a good result for this kind of instruments. really suggested. Thanks both to aneng and bangood

ANENG ST209 Digital Multimeter Clamp Meter 6000 Counts True RMS Amp DC/AC Current Clamp Tester Meters Voltmeter 400V Auto Range

US$29.69 US$39.99

1

Comments (0)

BG473457484 18/06/2021

it a basic item is perfect for creating lithium battery pack

5M Pure Nickel Strip 99.96% 18650 Battery Spot Welding Machine Welder Equipment Nickel Belt for Battery Packs

US$5.99 US$12.98

0

Comments (0)

BG473457484 18/06/2021

machine arrived on time. the battery was dead so I charged for a while (15 minutes) then the appliance boot up and I was able to solder a couple of AAA batteries. it's very simple to use I kindly suggest it

1S Mini Spot Welder Welding Machine DIY 18650 Lithium Battery Nickel Belt Spot Welding Portable Household Fiber Welding Machine

US$42.75 US$68.99

0

Comments (0)

BG473457484 thanks after a couple of weeks I ordered the cable with the right connector and everything worked fine

BG473457484 13/09/2020

Hello everyone, I would like to share my experience with this product that I used to replace the mainboard of one of my old led TV that I'm currently using as secondary monitor. I suggest to follow the instruction to assure the compatibility with your panel, I don't know if the provided cable is compatible with my panel, because I used the old one . Another thins that could help some is that I used my led inverter instead of the provided one, just check that your is pin to pin compatible with the board (check VCC and GND and Enable pins position(. The boards come with a factory software that was not compatible with my panel but I just used the VST53C_4MB_M.bin for my resolution, I noticed that the vendor developed specific software version for specific panel, so I suggest to check if there's a version for your panel before using the general. I was able to place all provided things inside the tv case and I like the results (you can judge, just check the uploaded photo). The job was not complicated but I checked pinout, compatibility and other stuffs a lot of time before that I decide to powered on my board, I think that if you will choose wrong panel VCC on pinout you can damage both board and panel so be careful!!! According to the audio IC datasheet I decided to leave disconnected the original audio speaker because both electrical power and impedance were not compatible (6W@4ohm for channel) , the provided IC is only 2ch for 2W@3ohm. I kindly suggest this kit if you need a cheap monitor or CCTV. I also suggest to read careful the provided manual just to prevent any damage on stuff or person. Unfortunately I have to highlight that I had some issues with shipment (the local courier delayed the delivery and bangood support cannot help me as I expected, Bangood please improve your support on after sales issue that will prevent any bad expirence), but finally after a lot of phone call I guessed the courier and I found my board. Hope this can help you guys!

T.SK105A.03 Universal LCD LED TV Controller Driver Board TV/PC/VGA/HDMI/USB+7 Key Button+2ch 6bit 30pins LVDS Cable+1 Lamp Inverter

US$18.99 US$25.99

5

Comments (2)

BG473457484 29/03/2021

item delivered quickly. all contents are as described suggested!

63 in 1 Multi-Tool Magnetic Precision Screwdriver Set Portable Phone Computer Repair Tools Kit

US$11.99 US$22.99

0

Comments (0)

BG473457484 10/11/2020

The package arrived in good condition. all items were preset as expected and are working fine. the installation instruction were not applicable completely to this item and I had to look on YouTube for a simplified instructions. The image quality are good and the item is simple to use. very suggested .

3.5X 7X 45X 90X Double Boom Stand Zoom Simul Focal Trinocular Stereo Microscope+41MP Camera Microscope For Industrial PCB Repair

US$624.59 US$832.99

0

Comments (0)

BG473457484 hi you cannot use the provide inverter because is for ccfl lamp and not for the led one. just use the original one or you can buy it from BG. keep in mind that the provided inverter use an high voltage and leds needs a lower voltage than ccfl lamp. stay safe.

BG152210105 19/07/2020

I purchased this kit as it looked liked it support my display which is a LTM200KT10, but the is a compatibility issues with the inverter plug from the board to the LED plug on the panel. Can you advise if it is possible to overcome this problem, I have attached images of the inverter plug on my display and the one from the inverter board vs one to panel. Thank you