All Messages

Alferboy It will run completely fine with any 5v power supply above 0.2amp. It'll only draw what it needs ( it's needs quite below 200mA ).

2021-09-17 02:16:13 Helpful (1)
Submit
Answers (4)

Q: Can I put knob to adjust the voltage and the current?

Asked by Ανεστης Παγτζογλου on 2021-02-14 05:25:49

Alferboy No. This is a fixed voltage power supply that is mainly to be used with the RD6006 or RD6006W power controllers, inside a S06A box. This will allow it to be fully voltage variable. I have one of these sets and it's awesome!! See the note: "Note: This power supply can be used with Product ID: 1587151 (RD6006 RD6006-W), S06A Case Product ID 1587330 (If you need to use with RD6006 RD6006-W, please select 60V)"

2021-02-15 01:36:19 Helpful (0)
Submit
Answers (5)

Q: Does this also work with the RD6018W power supply?

Asked by BG035125420 on 2021-01-27 02:41:51

Alferboy From what I see it's the same size has the one I have for the RD6006W, so it's most likely. The size is standard.

2021-01-29 02:57:09 Helpful (1)
Submit
Answers (4)

Q: DOES IT COME WITH DIRECTIONS?

Asked by kevinpittsburgh on 2020-07-08 11:30:44

Alferboy None that I recall

2020-07-08 11:43:41 Helpful (0)
Submit
Answers (7)

Alferboy O "pente" tem um "ponto" numa das pontas. Esse ponto deve correponder ao pequeno quadrado na placa. O fio azul deve ser engano. Tem 3 pontos de alimentação na placa. A ficha, os dois pontos ao lado da ficha para ligar a alimentação e os outros dois pontos do lado direito da placa que servem para ligar uma bateria de 3v para manter a hora quando falta a energia.

2020-07-02 04:50:10 Helpful (1)
Submit
Answers (1)

Q: Can we obtain the file to program in case we clear the 2051 ?

Asked by Alferboy on 2020-06-27 10:44:08

CutieePie Should be like this

2020-07-02 03:55:06 Helpful (0)
Submit
Answers (1)

Alferboy You should read your board's documentation. Most of these sensors will work with 3,3v or 5v. Your board seems to use mainly 3.3v logic. For everything digital, if you pullup on the board side you should be ok. But you'd better make sure if your board is 5v logic tolerable (I think there's a set of pins where it is).

2020-05-08 07:52:57 Helpful (0)
Submit
Answers (9)

Q: How many usages per cap??

Asked by Alferboy on 2020-02-03 01:02:32

daffster13 Approx 15,836,452,398,763. But results may vary. 😁

2020-02-10 07:42:05 Helpful (0)
Submit
Answers (1)

mareklew Other devices connected to grid, including your grid feed transformer, provide a short between the AC contacts. Bulb recognizes that a) there's no AC voltage and b) the contacts have electric path between them and powers on.

2020-01-21 02:15:09 Helpful (6)
Submit
Answers (1)

mmm456 Снимите и установите часовую стрелку, как вам нужно. Rotate the hour hand manually as you need.

2020-01-15 06:26:14 Helpful (1)
Submit
Answers (2)